MANIAC - pre-wash for foam guns 1000ml for Car detailing

A pre-wash for car detailing foam guns, Foam Gun Prewash MANIAC cleans, polishes and protects all exterior surfaces. It removes smog, road dirt, insects, and organic residue from plants or birds. It can be used frequently as it respects previously applied protective layers, including nano-technology based protectants or coatings. This multi-purpose product is designed for use with both a pump sprayer and a foam lance. Using it with a pressure washer enhances the safety of the subsequent washing phase, as it removes 90% of dirt and lets you wash the car without the risk of creating swirls or micro-scratches. We recommend using a foam gun or a low-pressure manual pump sprayer.

How to use:
With a hand sprayer for local action on specific dirt: If you apply the product at low pressure, diluted 1:10 (1 part product to 10 parts water) directly onto the dirt, you will achieve a high-performance, localised effect, ideal for stubborn dirt like insect residue or mud.
With a low-pressure manual pump sprayer: The product can be used with a low-pressure manual pump sprayer, diluting Foam Gun Prewash 1:50 in winter (1 part product to 50 parts water), which is 2 caps per 1 litre of water, or 1:100 in summer (1 part product to 100 parts water), which is 1 cap per 1 litre of water.
Spray the product and let it work for 1 minute to separate the dirt from the surface. Finally, rinse thoroughly with a high-pressure jet of water, using the water jet to remove coarse dirt residue. The kinetic energy from the pressure washer will remove the dirt that the gentle action of the pre-wash has loosened from the surface. In summer, or if working in the sun and at high temperatures, it is recommended to wash and rinse one part of the vehicle at a time.
For lower sections and localised dirt, apply the diluted product directly from the bottom up and rinse. Then apply the product in foam gun mode, always from the bottom up according to the dosage. Apply a thick layer of foam to the vehicle and wait for it to start running down (this can take up to 5 minutes). Finally, rinse with a high-pressure jet of water from top to bottom.
Dosage:
For winter dirt: 1:5 (1 part product and 5 parts water) to achieve a final dilution of 1:50 at the outlet
For summer dirt: 1:10 (1 part product and 10 parts water) to achieve a final dilution of approximately 1:110 at the outlet.
​
Recommendations:
To prevent the shampoo from drying and causing stains, wash the car in the shade and never in direct sunlight.
If the vehicle has been in the sun or the bonnet is very hot, cool the surface with a stream of cold water.
Start from the roof – it's the least dirty part, so you'll avoid getting your mitt dirty: washing will be faster.
Try using two buckets – put the water and shampoo solution in the first, and just water in the second, which you use to frequently rinse your sponge or mitt: this will prevent scratching the bodywork.
Wash in small sections – You won't miss any spots, the product will be able to work as effectively as possible without drying out: you'll avoid stains and streaks.
Perfect circles – use a brush to clean the rims to get into even the most hidden places.

Warning:
Do not use on motorcycles.
H318: Causes serious eye damage.H315: Causes skin irritation.P102: Keep out of reach of children.P280: Wear protective gloves and eye protection.P302+P352: IF ON SKIN: Wash with plenty of water.P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.P332+P313: If skin irritation occurs: Get medical advice/attention.P337+P313: If eye irritation persists: Get medical advice/attention.P501: Dispose of contents/container in accordance with local, regional, national or international regulations.